940 Каталог KYOCERA 2019 Режущий инструмент для металлообработки на станках Стр.L192

Каталог KYOCERA 2019 Режущий инструмент по металлу Стр. L192 0940 Lab2u

RECOMMENDED CUTTING CONDITIONS Drilling - Standard Solid Carbide Micro Spotting Drills Series 080 / 081 Workpiece Material Material Hardness/Types Uncoated Recommended Cutting Speed AlTiN Coated Recommended Cutting Speed Cutting Dia. DC (in) Cutting Dia. DC (mm) Feed Per Rev (sfm) (m/min) (sfm) (m/min) (ipr) (mm/rev) Low Carbon Steel 12L14 A36 260 330 80 - 100 330 395 100 120 00.010 00.25 0.0005 0.013 00.020 00.50 0.00098 0.025 00.040 01.00 0.00196 0.050 00.080 02.00 0.0039 0.100 00.125 03.00 0.0047 0.120 Mild Carbon Steel 1018 1028 1050 195 295 60 90 260 360 80 - 110 00.010 00.25 0.0005 0.013 00.020 00.50 0.00098 0.025 00.040 01.00 0.00196 0.050 00.080 02.00 0.0039 0.100 00.125 03.00 0.0047 0.120 Stainless Steel 303 304 316 321 100 165 30 50 130 195 40 60 00.010 00.25 0.00029 0.007 00.020 00.50 0.00059 0.015 00.040 01.00 0.00118 0.030 00.080 02.00 0.00236 0.060 00.125 03.00 0.00354 0.090 Stainless Steel 15-5PH 17-4PH 13-8 400 Series 60 - 100 18 30 80 - 140 25 42 00.010 00.25 0.00022 0.006 00.020 00.50 0.00044 0.012 00.040 01.00 0.00088 0.024 00.080 02.00 0.00176 0.043 00.125 03.00 0.00264 0.067 Gray Cast Iron 260 330 80 - 100 330 395 100 120 00.010 00.25 0.00049 0.012 00.020 00.50 0.00098 0.025 00.040 01.00 0.00196 0.050 00.080 02.00 0.00392 0.100 00.125 03.00 0.00588 0.120 Nodular Cast Iron 195 295 60 90 230 295 70 90 00.010 00.25 0.00039 0.010 00.020 00.50 0.00078 0.020 00.040 01.00 0.00157 0.040 00.080 02.00 0.00314 0.080 00.125 03.00 0.00471 0.120 Aluminum 330 590 100 180 490 655 150 200 00.010 00.25 0.00059 0.015 00.020 00.50 0.00118 0.030 00.040 01.00 0.00236 0.060 00.080 02.00 0.00472 0.120 00.125 03.00 0.00708 0.180 Copper Alloys 295 395 90 - 120 360 460 110 140 00.010 00.25 0.00059 0.015 00.020 00.50 0.00118 0.030 00.040 01.00 0.00236 0.060 00.080 02.00 0.00472 0.120 00.125 03.00 0.00708 0.180 Heat Resistant Alloy Hastelloy Inconel Monel Waspaloy 80 - 115 25 35 100 130 30 40 00.010 00.25 0.00246 0.062 00.020 00.50 0.00492 0.013 00.040 01.00 0.00984 0.025 00.080 02.00 0.01970' 0.500 00.125 03.00 0.02954 0.750 Titanium Alloy 90 - 115 27 35 100 130 30 40 00.010 00.25 0.00029 0.007 00.020 00.50 0.00059 0.015 00.040 01.00 0.00118 0.030 00.080 02.00 0.00236 0.060 00.125 03.00 0.00354 0.090 9S3 ° w ¥ BORING BARS Recommended starting parameters based on good setup, minimum tool runout & good tooling Note: These tools can also be used in PLASTICS, when doing so use the parameters for aluminum listed above Above recommendations are suggested starting parameters. Cutting speeds and feed rates may vary according to machining application and setup. DRILLS END MILLS ROUTERS THREAD MILLS ENGRAVERS REAMERS TECHNICAL (U.S.) 1.888.848.8449 I 192 (International) 001.714.428.3636 L192 Visit us online at