1015 Каталог TUNGALOY 2017 Металлорежущий инструмент и станочная оснастка Стр.E065

Каталог TUNGALOY 2017 Режущий инструмент и оснастка Стр. E065 1015 ENG Lab2u

FDC L/D = 8 (L type) Designation Обозначение по каталогу 0Dc G1F 0Ds I Is L Designation Обозначение по каталогу 0Dc G1F 0Ds I Is L FDC0500L 5 5 55 38 95 FDC0760L 7.6 8 88 42 130 FDC0510L 5.1 6 61 40 105 FDC0770L 7.7 8 88 42 130 FDC0520L 5.2 6 61 40 105 FDC0780L 7.8 8 88 42 130 FDC0530L 5.3 6 61 40 105 FDC0790L 7.9 8 88 42 130 FDC0540L 5.4 6 61 40 105 FDC0800L 8 8 88 42 130 FDC0550L 5.5 6 61 40 105 FDC0810L 8.1 9 94 44 140 FDC0560L 5.6 6 66 40 110 FDC0820L 8.2 9 94 44 140 FDC0570L 5.7 6 66 40 110 FDC0830L 8.3 9 94 44 140 FDC0580L 5.8 6 66 40 110 FDC0840L 8.4 9 94 44 140 FDC0590L 5.9 6 66 40 110 FDC0850L 8.5 9 94 44 140 FDC0600L 6 6 66 40 110 FDC0860L 8.6 9 99 44 145 FDC0610L 6.1 7 72 40 115 FDC0870L 8.7 9 99 44 145 FDC0620L 6.2 7 72 40 115 FDC0880L 8.8 9 99 44 145 FDC0630L 6.3 7 72 40 115 FDC0890L 8.9 9 99 44 145 FDC0640L 6.4 7 72 40 115 FDC0900L 9 9 99 44 145 FDC0650L 6.5 7 72 40 115 FDC0910L 9.1 10 105 44 150 FDC0660L 6.6 7 77 40 120 FDC0920L 9.2 10 105 44 150 FDC0670L 6.7 7 77 40 120 FDC0930L 9.3 10 105 44 150 FDC0680L 6.8 7 77 40 120 FDC0940L 9.4 10 105 44 150 FDC0690L 6.9 7 77 40 120 FDC0950L 9.5 10 105 44 150 FDC0700L 7 7 77 40 120 FDC0960L 9.6 10 110 46 160 FDC0710L 7.1 8 83 42 125 FDC0970L 9.7 10 110 46 160 FDC0720L 7.2 8 83 42 125 FDC0980L 9.8 10 110 46 160 FDC0730L 7.3 8 83 42 125 FDC0990L 9.9 10 110 46 160 FDC0740L 7.4 8 83 42 125 FDC1000L 10 10 110 46 160 FDC0750L 7.5 8 83 42 125 Line-up 5 < 0Dc < 6 6 < 0Dc < 10 tolerance (mm) +0.02 +0.01 +0.025 +0.015 Cutting fluid Supply the cutting fluid through the drill. The required fluid pressure is 0.5 to 1.0 MPa Use a water soluble cutting fluid containing a large amount of extreme pressure additive. STANDARD CUTTING CONDITIONS Стандартные режимы резания ISO Workpiece material Обрабатываемый материал Aluminium alloys Алюминиевые сплавы Cutting speed: Vc (m/min) N Grey Cast irons Ductile cast irons 05 08 100 - 140 90 - 120 60 - 80 08 012 120 - 160 110 - 140 70 - 90 012 016 140 - 180 130 - 160 70 - 100 05 08 0.1 - 0.25 0.1 - 0.25 0.1 - 0.25 Feed Подача f (mm/rev) 08 012 0.15 - 0.3 0.2 - 0.3 0.15 - 0.3 012 016 0.15 - 0.3 0.2 - 0.30 0.15 - 0.3 Caution: When changing a tool, completely clean the chips which may be clogging in the collet or adapter. Note: The cutting conditions shown left may vary depending on the work material, coolant dilution ratio and coolant supply pressure used. CUTTING PERFORMANCE Work materials: FC300 (200HB) f = 0.3 mm/rev m/min 5 6 7 8 9 10 11 12 13 14 15 16 Drill diameter 0Dc (mm) 3200 2800 V 2400 2000 % 1600 1200 800 400 Work material: FC300 (200HB) Cutting conditions: Vc = 120 m/min Ge'i. 5 6 7 8 9 10 11 12 13 14 15 16 Drill diameter 0Dc (mm) > No. of revolutions (min-1) = Cutting speed x 1000 + 3.14 + Tool diameter > Table feed (mm/min) = No. of revolutions x Feed per revolution Tungaloy E065