TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS

TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS

TAPER RADIUS BALL SQUARE carbide Концевые фрезы Mitsubishi по металлу со сменными режущими твердосплавными головками CARBIDE INDEXABLE HEAD END MILLS _ IMX-C4HV Рекомендуемые режимы резания при обработке на станке RECOMMENDED CUTTING CONDITIONS Side milling Work material Carbon steel, Alloy steel, Mild Steel, Copper, Copper alloys AIS11045, AISI 4140, ASTM A36, AIS11010 Pre-hardened steel, Carbon steel, Alloy steel, Alloy tool steel AISI P21, AISI P20, AISI 4340, SKD, SKT Austenitic stainless steel, Ferritic and Martensitic stainless steel, Titanium alloys AISI 304, AISI 316, AISI 304LN, AISI 316LN, AISI 410, AISI 430, AISI 431, AISI 420J2, Ti-6AI-4V LID Dii DC(mm) Cuttiig spnd (minin) Rnduton (nin-1 Fssd psr Tooth (nsn/lodti Tsbis Fssd (nmMn) Dqidcut M Mild cut ii(mm Cutting spud mMi Revdution min-1) Fssd psi Toolh (mmM) Tsbis Fssd (mmlmin) Dipth d cut (nil) Width of cut ai mm Cutting spnd (minin Rsvalution (mW Fssd psr Tooth (nmltooth) Tsbis Fssd (mm/min) Dspth of cut (mm Width of cut ss(nm 4 16 100 2000 0.09 720 32 0.8 80 1600 0.07 450 32 0.8 60 1200 0.08 380 32 0.8 20 100 1600 0.09 580 40 1 80 1300 0.07 360 40 1 60 950 0.08 300 40 1 6 16 60 1200 0.07 340 32 0.8 50 990 0.05 200 32 0.8 40 800 0.06 190 32 0.8 20 60 950 0.07 270 40 1 50 800 0.05 160 40 1 40 640 0.06 150 40 1 ae Work material Precipitation hardening stainless steel, Cobalt chromium alloy AISI 630, AISI 631 Heat resistant alloys lnconel718 LID Dii DC(m Cutting spied (minin Revdution (mW Feed per Tooth (inilM Table Feed (mmlmin) Depth of cut Whloicut n mti Cling speed tnimin) Revolution min-1) Feed per M (mmltootti TibleFeed (mmlmii) Depth of at (mm) Width of cut ii(mni) 4 16 50 990 0.07 280 32 0.8 30 600 0.05 120 32 0.4 20 50 800 0.07 220 40 1 30 480 0.05 96 40 0.5 6 16 30 600 0.05 120 32 0.8 20 400 0.04 64 32 0.4 20 30 480 0.05 96 40 1 20 320 0.04 51 40 0.5 ae For stainless steel, titanium alloy and heat resistant alloy, the use of water-soluble coolant is effective. If the depth of cut is shallow, the revolution and feed rate can be increased. The irregular helix flute end mill has a large effect on controlling vibration when compared to standard end mills. However, if the rigidity of the machine or the workpiece installation is poor, vibration or abnormal sound can occur. In this case, please reduce the revolution and feed rate proportionately, or set a lower depth of cut. The length of the long cutting type is 2 times that of the standard head. L/D demonstrates +1 when installed to a holder of the same size. 1252 Mitsubishi Materials